Smithco Sand Star Zee 45-501-A, Parts & Service

Page: 43 / 69

41
Accessories
INSTALLATION INSTRUCTIONS
1� Make sure machine engine is off and the key is removed� Set the parking brake�
2� Assemble Pusher Bars (Ref� 10, 11) to Front Cross-tube (Ref� 12) using
3
/
8
x 2
1
/
4
Bolts and
3
/
8
Nylon
Lock Nuts (Ref� 11) � Pusher Bars should be on the inside of the mounting plates on the Front Cross-
tube�
3� Attach the Plow Blade (Ref� 13) to the Front Cross-tube (Ref� 12) using
1
/
2
x 1
1
/
2
Bolts and
1
/
2
Nylon
Lock Nuts (Ref� 16) and
3
/
8
x 1
1
/
4
Bolts,
3
/
8
Flat Washers and
3
/
8
Nylon Lock Nuts (Ref� 17) � When tight-
ening hardware, set the plow angle to be more or less aggressive, which ever is your preference�
4� Connect Pusher Bars
(Ref� 10, 11)
to the upper holes of the mount brackets on the mainframe using the
1
/
2
x 2 Clevis Pins
(Ref� 20)
and Bridge Pins
(Ref� 21)
�
NOTE:
If installing on a 45-500-A machine that has a center mounted attachment, the pusher bar
mount tabs slide in between the center attachment tabs� The pin then goes through all tabs�
(Fig� 3a,
3b)
5� Attach the Lift Assembly
(Ref� 7)
through the four slots in the bearing tube plates using the
5
/
16
x 3
1
/
2
Bolts and
5
/
16
Nylon Lock Nuts
(Ref� 19)
�
5b. If your machine does not have the mounting holes it will be necessary to drill the holes� Start by
clamping the Lift Assembly to the bearing tube plates so that it is centered side to side and the Lift As-
sembly mount plates are flush (Fig� 4) with the front of the bearing tube plates� It may be necessary to
remove the floorboard to drill straight through the bearing tube plates.
6� Install Lift Arms (Ref� 8) onto Pusher Bars using
3
/
8
x 2
1
/
2
Bolts,
3
/
8
Washers and
3
/
8
Nylon Lock Nuts
(Ref� 9) � If mounting to model 45-500 use the top hole on the Lift Arms (Fig� 1) � For model 45-501 use
the middle hole on the Lift Arms (Fig� 2) � Tighten hardware until snug� Do not over tighten, the Lift Arms
should be free to rotate but not be loose side to side�
7� Thread one,
1
/
2
- 20 Jam Nut (Ref� 6) , to each of the Lift Arms until it is
1
/
4
inch from the bottom� Then
thread the Rod End (Ref� 4) down to the Jam Nut. Mount to the Lift Assembly (Ref� 7) arms on the
inside (next to the spacer)� Use the
1
/
2
x 2
1
/
2
Bolts and
1
/
2
Nylon Lock Nuts (Ref� 5) to secure� Tighten
hardware�
8� Install Pedal Pad (Ref� 2) onto Pedal Stud (Ref� 3) securing with one
5
/
8
Jam Nut (Ref� 1) � Mount to Lift
Assembly as illustrated using the other
5
/
8
Jam Nut. The forward most Pedal mounts facing the Left and
the rearward Pedal mounts facing the right as illustrated�
9� Check the operation of the lifting mechanism and the levelness of the plow� If adjustment is necessary,
it may be done by adjusting the Lift Arms (Ref� 8) at the connection with the Rod Ends�