Smartgen ACC4100 User Manual Download Page 47

Page: 47 / 52

ACC4100 Diesel Air Compressor Controller User Manual Page 47 of 52

14.9

DEUTZ EMR2

Engine type: Volvo-EDC4.

Table 29 F Connector

Terminals of controller

F connector

Remark

Fuel relay output

Expansion

30A

relay,

providing battery voltage
for 14; Fuse is 16A.

Starting relay output

Connect to starter coil directly.

Connect to battery negative pole.

CAN(H)

Impedance 120Ω connecting line is
recommended.

CAN(L)

Impedance 120Ω connecting line is
recommended.

14.10

JOHN DEERE

Engine type: John Deere.

Table 30 21-pin Connector

Terminals of controller

21 pins connector

Remark

Fuel relay output

G, J

Starting relay output

CAN(H)

Using impedance 120Ω connecting line.

CAN(L)

Using impedance 120Ω connecting line.

14.11

MTU MDEC

Suitable for MTU engines, 2000 series, 4000series; Engine type:

mtu-MDEC-303.

Table 31 X1 Pin Connector

Terminals of controller

X1 connector

Remark

Fuel relay output

BE1

Starting relay output

BE9

Communication shielding line (connect with
ECU this terminal only).

CAN(H)

Using impedance 120Ω connecting line.

CAN(L)

Using impedance 120Ω connecting line.

Summary of Contents for ACC4100





















































Search results

Summary of Contents for ACC4100

Reviews:

Related manuals for ACC4100

Brands by name

Popular brands

Smartgen ACC4100, User Manual

Search results

Summary of Contents for ACC4100

Reviews:

Related manuals for ACC4100

Brands by name

Popular brands