Smartgen ACC4100 User Manual Download Page 28 | Manualshive

Page: 28 / 52

background image

ACC4100 Diesel Air Compressor Controller User Manual Page 28 of 52

No.

Item

Range

Default

Description

1: Normally Close

Alternate Configuration Setting
Alternate Configuration 1
1

Enable Choose

(0-1)

0

0: Disable 1: Enable

2

Engine Rated Speed

(0-6000)r/min 2200

When this is enabled, if input is configured
to  “Alt  Config.  1  Active”,  and  if  input  is
active,  speed  shall  be  adjusted  according
to  alternate  configuration  settings  after
load.

3

Engine Unload Speed

(0-100.0)%

70.0

4

Air

Com.

Rated

Pressure

(0-30000)kPa 700

5

Air Com. Unload Act
Press

(0-30000)kPa 600

Alternate Configuration 2
1

Enable Choose

(0-1)

0

0: Disable 1: Enable

2

Engine Rated Speed

(0-6000)r/min 2200

When this is enabled, if input is configured
to  “Alt  Config.  2  Active”,  and  if  input  is
active,  speed  shall  be  adjusted  according
to  alternate  configuration  settings  after
load.

3

Engine Unload Speed

(0-100.0)%

70.0

4

Air

Com.

Rated

Pressure

(0-30000)kPa 700

5

Air Com. Unload Act
Press

(0-30000)kPa 600

Alternate Configuration 3
1

Enable Choose

(0-1)

0

0: Disable 1: Enable

2

Engine Rated Speed

(0-6000)r/min 2200

When this is enabled, if input is configured
to  “Alt  Config.  3  Active”,  and  if  input  is
active,  speed  shall  be  adjusted  according
to  alternate  configuration  settings  after
load.

3

Engine Unload Speed

(0-100.0)%

70.0

4

Air

Com.

Rated

Pressure

(0-30000)kPa 700

5

Air Com. Unload Act
Press

(0-30000)kPa 600

Maintenance Setting
1

Oil Filter Set

(0-1)

0

0: Disable        1: Enable
Maintenance  time,  maintenance  time  due
action,  maintenance  timing  method,
maintenance time reset can also be set at
the  same  time;  After  maintenance,
maintenance  time  due  alarm  can  be
removed  by  resetting  maintenance  time;
Please refer to Table 14 for details.

2

Oil Separator Set

(0-1)

0

3

Air Filter Set

(0-1)

0

4

Lubrication Set

(0-1)

0

5

Engine Oil Filter Set

(0-1)

0

6

Engine Fuel Filter Set

(0-1)

0

7

Engine Lubrication Set

(0-1)

0

8

Maintenance 8 Set

(0-1)

0

9

Maintenance 9 Set

(0-1)

0

10

Maintenance 10 Set

(0-1)

0

NOTES

:

—

Regarding parameter setting on PC software, it isn't needed to input default factory password “1234” if not changed;
if it is the first time to do configuration on PC, then it is needed to input module password in password screen;

—

Digital input ports cannot be set the same items (except for user-defined). Otherwise function shall not work
correctly; Output ports can be set the same item;

—

Engine temperature related settings: if it is ordinary engine and engine temperature is needed, any one of flexible
sensors 1~4 shall be set engine temperature sensor; and at the same time curve type shall be set the

«
...
26
27
28
29
30
...
»

Summary of Contents for ACC4100





















































Reviews:

No comments

Related manuals for ACC4100

Brand: wattio Pages: 20

Brand: Babybee Pages: 28

TLE Scalable 150

Brand: GE Pages: 6

Brand: GE Pages: 3

Brand: GE Pages: 80

PACSystems* RX3i

Brand: GE Pages: 39

PACSystems* RX3i

Brand: GE Pages: 35

PACSystems* RX3i

Brand: GE Pages: 3

PACSystems* RX3i

Brand: GE Pages: 169

PACSystems RX7i

Brand: GE Pages: 317

Brand: Yudian Pages: 26

Brand: Salda Pages: 20

Brand: J3C Pages: 2

Brand: Harmonic Drive Pages: 85

Brand: LANGER EMV-Technik Pages: 48

Brand: Rain Bird Pages: 138

Brand: u-blox Pages: 28

Brand: u-blox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands