Smartgen ACC4100 User Manual Download Page 44

Page: 44 / 52

ACC4100 Diesel Air Compressor Controller User Manual Page 44 of 52

14.3

CUMMINS QSM11(IMPORT)

Suitable for CM570 engine control module; Engine type is QSM11 G1, QSM11 G2; Engine type:
Cummins ISB.

Table 20 C1 Connector

Terminals of controller

C1 connector

Remark

Fuel relay output

5&8

Outside extended relay, make port 5 and port
8 of C1 connected at fuel output;

Starting relay output

Connect to starter coil directly.

Table 21 3-pin Data Link Connector

Terminals of controller

3 pins data link connector

Remark

CAN communication shielding line (connect
with ECU terminal only).

CAN(H)

Using impedance 120Ω connecting line.

CAN(L)

Using impedance 120Ω connecting line.

14.4

CUMMINS QSX15-CM570

Suitable for CM570 engine control module; Engine type is QSX15 etc. Engine type: Cummins
QSX15-CM570.

Table 22 50-pin Connector

Terminals of controller

50 pins connector

Remark

Fuel relay output

Oil spout switch.

Starting relay output

Connect to starter coil directly.

Table 23 9-pin Connector

Terminals of controller

9 pins connector

Remark

SAE J1939 shield-E

CAN communication shielding line (connect
with ECU terminal only).

CAN(H)

SAE J1939 signal-C

Using impedance 120Ω connecting line.

CAN(L)

SAE J1939 return-D

Using impedance 120Ω connecting line.

Summary of Contents for ACC4100





















































Search results

Summary of Contents for ACC4100

Reviews:

Related manuals for ACC4100

Brands by name

Popular brands

Smartgen ACC4100, User Manual

Search results

Summary of Contents for ACC4100

Reviews:

Related manuals for ACC4100

Brands by name

Popular brands