Smartgen ACC4100 User Manual Download Page 48

Page: 48 / 52

ACC4100 Diesel Air Compressor Controller User Manual Page 48 of 52

14.12

MTU ADEC (SMART MODULE)

Suitable for MTU engine with ADEC (ECU8) and SMART module; Engine type: mtu-ADEC.

Table 32 ADEC (X1 Port)

Terminals of controller

ADEC (X1port)

Remark

Fuel relay output

X1 10

X1 Terminal 9 connected to negative of battery.

Starting relay output

X1 34

X1 Terminal 33 connected to negative of battery.

Table 33 ADEC (X4 Port)

Terminals of controller

SMART (X4 port)

Remark

CAN(H)

X4 1

Using impedance 120Ω connecting line.

CAN(L)

X4 2

Using impedance 120Ω connecting line.

14.13

MTU ADEC (SAM MODULE)

Suitable for MTU engine with ADEC (ECU7) and SAM module; Engine type: Common J1939.

Table 34 ADEC (X1 Port)

Terminals of controller

ADEC (X1port)

Remark

Fuel relay output

X1 43

X1 Terminal 28 connected to negative of battery.

Starting relay output

X1 37

X1 Terminal 22 connected to negative of battery.

Table 35 SAM (X23 Port)

Terminals of controller

SAM (X23 port)

Remark

CAN(H)

X23 2

Using impedance 120Ω connecting line.

CAN(L)

X23 1

Using impedance 120Ω connecting line.

14.14

PERKINS

Suitable for ADEM3/ADEM4 engine control module; Engine model is 2306, 2506, 1106, and 2806.
Engine type:

Perkins.

Table 36 Connector

Terminals of controller

Connector

Remark

Fuel relay output

1, 10, 15, 33, 34

Starting relay output

Connect to starter coil directly.

CAN(H)

Using impedance 120Ω connecting line.

CAN(L)

Using impedance 120Ω connecting line.

Summary of Contents for ACC4100





















































Search results

Summary of Contents for ACC4100

Reviews:

Related manuals for ACC4100

Brands by name

Popular brands

Smartgen ACC4100, User Manual

Search results

Summary of Contents for ACC4100

Reviews:

Related manuals for ACC4100

Brands by name

Popular brands