Skope OD1100N Service Manual Download Page 33

33

SKOPE OD1100N

Replacement Procedures

Service Manual

The fan motors and fan blades are fixed to the evaporator shroud with brackets. The shroud 

(complete with fan motors and fan blades) can be lifted off the evaporator tub. 

It is important that fan blades and fan motors are replaced with the same part to ensure safety, 

correct alignment and refrigeration performance, and compliance. When refitting or replacing 

fan motors, ensure that the blade screw is tightened to 1.5 Nm.

Fan motor

Evaporator shroud

Evaporator tub

Mounting 

bracket

IMPORTANT

Replace the motor with the same SKOPE OEM part.

DO NOT

 use alternative parts.

Procedure 22: To access the evaporator fan assembly

1. Disconnect the cabinet from the power supply (see page 18).

2. Remove the refrigeration cartridge (see page 28). The evaporator fan assembly can now be 

accessed.

Procedure 23: To replace the evaporator fan blade

1. Disconnect the cabinet from the power supply (see page 18).

2. Remove the refrigeration cartridge (see page 28).

3. Remove the screw and washer from the centre of the fan blade, and lift the blade from the motor.

4. Ensure the new blade is centred within the evaporator shroud, and reattach with a 12 mm flat 

washer and serrated head screw. Tighten the screw to 1.5 Nm.

5. Reassemble the cartridge and test for correct operation:

“To diagnose lack of gas” on page 27.

Test and tag.

Procedure 24: To replace the evaporator fan motor

1. Follow Procedures 22 and 23 to access the evaporator fan assembly and remove the fan blade.

2. Unscrew and remove the cartridge’s right hand side panel to access the fan motor cable 

connectors.

3. Lift the evaporator shroud (complete with fan motor) from the evaporator tub.

Note

: The evaporator and control probe flexible cords may restrict movement when lifting the 

shroud from the evaporator tub.

4. Free the fan flexible cord by cutting the cable ties and removing it from the evaporator tub edge 

putty.

5. Remove the four nuts and spring washers from the fan mounting brackets and lift the fan motor 

from the bracket.

Summary of Contents for OD1100N



















































Reviews: