Sinclair ASCU-12A Service Manual Download Page 65

Page: 65 / 202

U-MATCH AIR CONDITIONERS INSTALLATION

Figure 1-2-11

Figure 1-2-12

1.3 Installation of Cassette Type

1.3.1 Before Installation

When the unit arrives, please check if any damage due to transport is existent. If any hurt is found on the

surface or inside, please declare to the transport company or the manufacturer in writing.

Upon receipt of the unit, the unit and accessories shall be checked in accordance with the packing list. Before

acceptance, it must be confirmed that the model is correct and the unit is in good shape and specification and

quantity of accessories are right.

Correct handling route and method shall be decided to prevent damage to the unit. For protecting the unit and

ensuring its safety, carrying the unit with its package is recommended. If such carrying method is difficult

under particular conditions, the canton shall not be removed to avoid looseness or falling during handling.

Confirm the foundation is secure. When the unit is installed on the metal part of a building, electrical

insulation must be in compliance with relevant standards.

Confirm the installation position is away from storage zone of inflammable and explosive substances, or

otherwise leakage of inflammable and explosive substances may lead to explosion or a fire.

1.3.2 Installation Site

Obstruct should put away from the intake or outlet vent of the indoor unit so that the airflow can be blown

though all the room.

Make sure that the installation had accord with the requirement of the schematic diagram of installation

spaces.

Select the place where can stand 4 times of the weight of the indoor unit and would not increase the

operating noise and oscillate.

The horizontally of the installation place should be guaranteed.

Select the place where is easy to drain out the condensate water, and connect with outdoor unit.

Make sure that there are enough space for care and maintenance. Make sure that the weight between the

indoor unit and ground is above 2300mm.

When installing the steeve bolt, check if the install place can stand the weight 4 times of the unit’s. If not,

reinforce before installation. (Refer to the install cardboard and find where should be reinforced) The

appliance shall not be installed in laundry.

Summary of Contents for ASCU-12A











































































































































































































Search results

Summary of Contents for ASCU-12A

Reviews:

Brands by name

Popular brands

Sinclair ASCU-12A, Service Manual

Search results

Summary of Contents for ASCU-12A

Reviews:

Brands by name

Popular brands