Sinclair ASCU-12A Service Manual Download Page 147

Page: 147 / 202

MAINTENANCE

146

Disassembly of fan and motor

Remark: Make sure the power supply is cut off before disassembling and protect all the parts during disassembly.

Step Illustration

Handling

Instruction

1. Disassembly of

fan

Disassemble the fixing screws

on the fan components. (As is

shown in Graph 10, circle

represents 6 screws.)

2. Disassembly of

motor

Disassemble the fastening

screws on the fan and motor.

Remove the fan. (As is shown

in Graph 11, box represents

screws.)

Disassembly of evaporator

Remark: Make sure the power supply is cut off and protect the copper tube and aluminum fin. If the time for disassembly shall

be long, put the copper tube under pressurized condition.

Step Illustration Handling

Instruction

1. Disassembly of

fixing screws on

the side panels of

evaporator

Disassemble the fastening screw

connecting left and right side

panels on the evaporator and the

upper cover plate. (As is shown in

the arrow’s direction in Graph 12.)

2. Disassemble

fastening screws

connecting

evaporator valve

seal-plate and joint

flange

Disassemble the fastening screws

on the valve seal-plate and remove

the valve seal-plate. Disassemble

the fastening screws on the

evaporator’s joint flange. (As is

shown in the graph, box represents

fastening screws on seal-plates

while circle the fastening screws on

joing flange.

Summary of Contents for ASCU-12A











































































































































































































Search results

Summary of Contents for ASCU-12A

Reviews:

Brands by name

Popular brands

Sinclair ASCU-12A, Service Manual

Search results

Summary of Contents for ASCU-12A

Reviews:

Brands by name

Popular brands