Sinclair ASCU-12A Service Manual Download Page 152

Page: 152 / 202

MAINTENANCE

151

Disassembly of evaporator components

Remark: Make sure the power supply is cut off and protect the copper tube and aluminum fin. If the time for disassembly shall

be long, put the copper tube under pressurized condition.

Step Illustration

Handling

Instruction

Disassembly of

evaporator

components

Disassemble the screws as

shown by the arrow in the

graph with screwdriver.

(There are 4 screws on left

and right of the evaporator

and 2 on evaporator outlet

press plate modules)

Disassembly of fixing plate modules for air sweeping fans

Remark: Make sure the power supply is cut off before disassembling and protect all the parts during disassembly.

Step Illustration

Handling

Instruction

Disassembly of

fixing plate modules

for air sweeping

fans

Disassemble the screws

shown in the graph with

screwdriver.

Disassembly of right and left polystyrene foam plates modules

Remark: Make sure the power supply is cut off before disassembling and protect all the parts during disassembly. Do not heat or

hit polystyrene foam modules.

Step Illustration

Handling

Instruction

Disassembly of

right and left

polystyrene foam

plates modules

Remove the right and left

polystyrene foam plates modules

in the direction given by the

graph.

Summary of Contents for ASCU-12A











































































































































































































Search results

Summary of Contents for ASCU-12A

Reviews:

Brands by name

Popular brands

Sinclair ASCU-12A, Service Manual

Search results

Summary of Contents for ASCU-12A

Reviews:

Brands by name

Popular brands