Silverline DIY 264569, Original Instructions Manual

Page: 6 / 46

GB
6
Included Accessories:
1 x Hex Key
Intended Use
• Multi-purpose rotary polishing machine, used for light to medium duty polishing and sanding
tasks, using suitable polishing bonnets, compounds and hook and loop sanding discs
Unpacking your Tool
• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features and
functions
• Ensure that all parts of the tool are present and in good condition . If any parts are missing or
damaged, have such parts replaced before attempting to use this tool
Before Use
Assembling the front handle
• The Front Handle (3) must be fitted to the machine before use:
1. Use the bolts supplied to fit the Front Handle (3) via the fixing holes to either side at the front of
the machine
2. Use the supplied hex key and tighten the bolts firmly, to secure handle in position
Fitting the Hook & Loop Backing Pad
• The Hook & Loop Backing Pad (8) must be securely fitted to the Spindle (1) before use:
1. Press and hold the Spindle Lock Button (2) with one hand, and slowly rotate the Spindle with the
other hand, until you feel it lock
2. The Hook & Loop Backing Pad can now be screwed onto the Spindle and tightened
WARNING: The Hook & Loop Backing Pad is tightened by hand. Take care not to cross-thread or
over-tighten .
3. Release the Spindle Lock Button
Fitting bonnets, polishing sponges and discs
• The Hook & Loop Polishing Bonnet (9), Hook & Loop Sanding Disc (10) and other polishing
accessories, such as polishing sponges (not included), can be pressed onto the face of the Hook
& Loop Backing Pad (8)
• Slowly pull the fitted attachment off the Hook & Loop Backing Pad to remove
Note: Always make sure both hook and loop surfaces are free of dirt and debris prior to attaching
any items (also see remarks ‘Maintenance’ section).
Operation
WARNING: Always wear adequate protective equipment, including eye, hand and hearing
protection, when operating this machine. Use respiratory protection where dust or fumes are
produced .
Switching on/off
WARNING: Never switch the tool on or off when it is in contact with the workpiece. This
can cause serious injury to the operator and will significantly shorten the service life of the On/
Off Switch (7).
1. Connect the machine to the mains power supply
2. To start the machine, depress the Lock-Off Button (5), and squeeze the On/Off Trigger Switch (7);
the motor will start and take a few moments to reach full operating speed
3. To stop the machine, release the On/Off Trigger Switch
Note: To operate the tool’s lock-on function, depress the Lock-On Button (5) whilst holding the On/
Off Trigger Switch
Note: To stop the tool once locked-on, squeeze and release the On/Off Trigger Switch
WARNING: ALWAYS wait until the machine has come to a standstill before putting it down.
Adjusting the tool speed
• The speed of the machine is controlled using the Speed Control Dial (4): a higher number
indicates a higher speed setting (also see label on the tool)
speed control
dial setting
approximate speed
(in rpm)
1 600
2 900
3 1,500
4 2,100
5 2,700
6 3,000
WARNING: Always set the Speed Control Dial to the correct speed for the task at hand.
WARNING: Never exceed the maximum speed of the installed accessory .
Polishing tips
• Ensure that the area to be polished is clean and dry
• Choose only polishing compounds that are compatible with the material to be polished, and
with the method of application. Read and understand all information supplied with your
polishing compound before use
• If using polishing sponges, apply polishing compound evenly to the polishing sponge and place
the sponge against the work surface
• Hold the machine securely, using both hands, by the handles provided . The polishing sponge
should make only light contact with the work surface
• Switch on the machine, and work across the surface using a wide 'sweeping' motion. Stop and
apply extra compound as required
• When the entire surface has been covered, stop the machine and allow the compound to dry
(follow manufacturer’s guidance)
• Attach a clean polishing bonnet to the machine and work across the surface as before, until all
visible polishing compound is removed
Sanding tips
WARNING: This machine is primarily designed as a polishing tool . It is suitable for light duty
sanding tasks, e.g. fine sanding as a preparation to polishing, but it has not been designed to
remove large amounts of material . Use a different type of sander, e .g . a belt sander, should this
be required.
WARNING: NEVER use this machine for wet sanding.
WARNING: ALWAYS use adequate respiratory protection when sanding.
• Allow the machine to reach the required speed before bringing the sanding paper into contact
with the workpiece
• Start with a coarse grit paper, and work through progressively finer grit papers until the desired
finish is achieved
• Apply only moderate pressure to the sander. Pressing too hard onto the work surface may
overheat the motor or damage the work surface
• Sand evenly over the work surface. The machine works in a rotary motion so it is not necessary
to work with the grain
• Only use the sander 'flat on' to the work. Tilting the sander onto its edge will damage your
workpiece
264569_MANUAL.indd 6 10/07/2017 12:13