www.silverlinetools.com
5
550W Dirty Water Pump Stainless Steel
869235
Electric Water Pump Safety
• The pump must always be transported, used, submerged, and stored
vertically. Only carry the pump by the lifting handle. Never carry, lift or
submerge the pump by its power cable
• This product is not designed for continuous use. Excessive usage will
shorten service life and invalidate the warranty
• DO NOT use this pump with substances other than water
• Sand and other abrasive material suspended in the liquid causes
increased wear and reduces the pump’s output capacity
• NEVER use this pump when ambient temperatures are close to freezing
• DO NOT attempt to operate the pump below the minimum water level as
this will cause permanent damage
• This device contains dangerous voltages. Never remove any part of the
casing
• Inspect the power cable and extension cord before every use to ensure
they are in good condition. ALWAYS have a damaged cable/extension
cable replaced by an authorised Silverline service centre. ONLY use
extensions with suitable cross section and outdoors rating. NEVER pull
the cable to disconnect it from the power socket. NEVER carry the tool by
its cable. NEVER touch live power cables or plug sockets with wet hands.
Keep the cable away from heat, oil, solvents and sharp edges
• ALWAYS observe local laws and regulations when connecting
submersible pumps to the power supply. Consult a qualified electrician
when necessary
• This pump must be operated exclusively on power points that are
protected by an RCD with a maximum tripping current of 30mA and a
maximum delay of 40ms
• DO NOT use this pump in swimming pools or ponds that are occupied
f)
Dress properly. Do not wear loose clothing or jewellery.
Keep your
hair, clothing and gloves away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving parts
g)
If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly
used.
Use of dust collection can reduce dust-related hazards
Power Tool Use & Care
a)
Do not force the power tool. Use the correct power tool for your
application.
The correct power tool will do the job better and safer at
the rate for which it was designed
b)
Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired
c)
Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive
safety measures reduce the risk of starting the power tool accidentally
d)
Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool.
Power tools are dangerous
in the hands of untrained users
e)
Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may
affect the power tool’s operation. If damaged, have the power
tool repaired before use.
Many accidents are caused by poorly
maintained power tools
f)
Keep cutting tools sharp and clean.
Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control
g)
Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working
conditions and the work to be performed.
Use of the power tool for
operations different from those intended could result in a hazardous
situation
Service
a)
Have your power tool serviced by a qualified repair person using
only identical replacement parts.
This will ensure that the safety of
the power tool is maintained
WARNING:
Before connecting a tool to a power source (mains switch power
point receptacle, outlet, etc.) be sure that the voltage supply is the same as
that specified on the nameplate of the tool. A power source with a voltage
greater than that specified for the tool can result in serious injury to the
user, and damage to the tool. If in doubt, do not plug in the tool. Using a
power source with a voltage less than the nameplate rating is harmful to
the motor.
869235_Z1MANPRO1.indd 5
13/03/2014 09:01
