General Safety
WARNING Read all safety warnings and all instructions.
Failure to
follow the warnings and instructions may result in electric shock, fire and/
or serious injury.
WARNING:
This appliance is not intended for use by persons (including
children) with reduced, physical or mental capabilities or lack of experience
or knowledge unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children must be supervised to ensure that they do not play with the
appliance.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
Work Area Safety
a)
Keep work area clean and well lit.
Cluttered or dark areas invite
accidents
b)
Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust.
Power tools
create sparks which may ignite the dust or fumes
c)
Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control
Electrical Safety
a)
Power tool plugs must match the outlet. Never modify the plug in
any way. Do not use any adapter plugs with earthed (grounded)
power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock
b)
Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators.
There is an increased
risk of electric shock if your body is earthed or grounded
c)
Do not expose power tools to rain or wet conditions.
Water
entering a power tool will increase the risk of electric shock
d)
Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock
e)
When operating a power tool outdoors, use an extension cord
suitable for outdoor use.
Use of a cord suitable for outdoor use
reduces the risk of electric shock
f)
If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply.
Use of an RCD
reduces the risk of electric shock
WARNING:
When used in Australia or New Zealand, it is recommended that
this tool is ALWAYS supplied via Residual Current Device (RCD) with a rated
residual current of 30mA or less.
Personal Safety
a)
Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in
serious personal injury
b)
Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard
hat, or hearing protection used for appropriate conditions will reduce
personal injuries
c)
Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your
finger on the switch or energising power tools that have the switch on
invites accidents
d)
Remove any adjusting key or wrench before turning the power
tool on.
A wrench or a key left attached to a rotating part of the power
tool may result in personal injury
e)
Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations
4
GB
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Class I construction (protective earth)
Risk of electrocution!
Conforms to relevant legislation and safety standards
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your local authority or retailer for recycling advice.
Specification
Voltage: .................................................................... 220-240V~, 50Hz
Power: ..................................................................... 550W
No load speed: ......................................................... 2860min
-1
Max flow rate: .......................................................... 175L/min
Maximum head height: ............................................ 7m
Minimum water level: .............................................. 50mm
Maximum submersion depth: .................................. 8m
Maximum particle size: ............................................ 20mm
Maximum water temp:............................................. 35˚C
Output hose connection: .......................................... 25 to 32mm
(1" to 1-
1
⁄
4
")
Cable length: ............................................................ 10m
Ingress protection: ................................................... IPX8
Protection class: ......................................................
Weight: .................................................................... 4.5kg
As part of our ongoing product development, specifications of Silverline products may
alter without notice.
869235_Z1MANPRO1.indd 4
13/03/2014 09:01
