4
GB
General Safety Instructions
Carefully read and understand this manual and any label attached to the tool
before use. Keep these instructions with the product for future reference.
Ensure all persons who use this product are fully acquainted with this
manual.
Even when used as prescribed it is not possible to eliminate all residual risk
factors. Use with caution. If you are at all unsure of the correct and safe
manner in which to use this tool, do not attempt to use it.
Accessories
• The use of any attachment or accessory other than those mentioned
in this manual could result in damage or injury. The use of improper
accessories could be dangerous, and may invalidate your warranty.
Check for damaged or missing parts
• Before each use, check if any part of the tool is damaged or missing,
check carefully that it will operate properly and perform its intended
function. Check alignment of moving parts for binding. Any guard or other
part that is damaged should be immediately repaired or replaced by an
authorised service centre.
Do not use if defective. Return to your
retailer.
Electrical Safety
To prevent fire or shock hazard, do not expose this product to rain/water
•
or moisture.
There are no user serviceable parts inside except those referred to in
•
this manual.
Always refer servicing to qualified service personnel. Never remove any
•
part of the casing unless qualified to do so; this unit contains dangerous
voltages.
Use of a residual current device will reduce the risk of electric shock.
•
Dangerous environment
Do not use power tools in damp or wet conditions, or expose them to
•
rain. Provide adequate surrounding work space and keep area well lit.
Do not use power tools where there is a risk of explosion or fire from
combustible material, flammable liquids, flammable gases, or dust of an
explosive nature. When using power tools avoid contact with any earthed
items such as pipes, radiators, cookers, refrigerators, metal
baths and taps.
Protect yourself from vibration
Hand held power tools may produce vibration. Vibration can cause
•
disease. Gloves to keep the operator warm may help to maintain good
blood circulation in the fingers. Hand held tools should not be used for
long periods without a break.
Maintain your power tool
Ensure all ventilation holes are kept clear at all times. Overheating and
•
fire may otherwise result.
Always disconnect
Before changing fittings or accessories, always ensure that your tool is
•
disconnected from the power source.
Switch off before connecting
Ensure that the power tool is switched off before connecting to the
•
power source. If the power tool stops unexpectedly, turn the power
switch to off.
Do not abuse the power cord
Be sure your cable/extension cable is in good condition. Always have a
•
damaged cable/extension cable replaced at an authorised service centre
before using it. Never pull the cable to disconnect it from the power
socket. Never carry your tool by its cable. Keep the cable away from
damp, heat, oil, solvents, and sharp edges.
Rechargeable Battery Safety
Use the battery charger correctly
Refer to the part of this manual relating to use of the battery charger
•
before attempting to charge the battery.
Do not attempt to use the charger, with any batteries other than those
•
supplied. Keep your battery charger clean, foreign objects or dirt may
cause a short, or block air vents.
Failure to follow these instructions may cause overheating or fire.
•
Use batteries correctly
Only charge batteries using charger provided. Only use batteries
•
provided with this power tool, or others recommended by the supplier.
Keep your batteries clean, foreign objects or dirt may cause a short.
Allow batteries to cool for 15 minutes after charging or heavy use.
Failure to follow these instructions may cause overheating or fire.
•
When not in use, batteries should be stored in a dry place, near to room
•
temperature (20˚C). Ensure that batteries cannot accidentally short in
storage.
Torch Safety
When the torch is switched on, the following must be followed.
•
Do not
look directly into the lens
•
Do not
shine the beam directly at any other person or animal’s eyes.
•
Do not
point the beam at: Cars, motorcycles, aircraft, ships or any other
vehicle or machinery that is operated by a person. Bright light can be
blinding and you could cause a serious accident.
Specification
Power: ................................................ 2 Million Candle Power
Battery Type: ...................................... 6V 4AH Battery
Bulb Type: .......................................... 6V H3 Halogen Bulb
Includes: ............................................. Mains & 12V Charger
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Wear head protection.
Wear hand protection.
Read instruction manual.
Class II construction (Double insulated).
Conforms to relevant legislation and safety standards.
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
282556_Instruction Manual.indd 4
29/12/10 16:14:39
