Siemens VersiCharge AC Installation And Operation Manual Download Page 32 | Manualshive

Page: 32 / 52

background image

5.2.1 Sign In:

white.

The Wi-Fi light will be blinking white. If not,

Please turn the charger off and on.

Sign in with email and password, select
Sign In or create an account by selecting
“Create One”.

Select Add a Charger.

Add a charger is the landing page until
a charger has been linked to your
account.

Step 1 – Check the Wi-Fi Light – it
should be blinking white.

Select Next.

Wi-Fi LED Light Sequence When Adding a Charger

Description of Sequence

LED Color (Blinking)

LED Color (Steady)

Power up

Software loading

Software running

Charger in Access Point (AP) mode

Receiving connection credentials

Received connection credentials

Connecting to network

Connected to network

Connecting to VersiCloud

Connected to network, registered and connected to VersiCloud

NOTE: Grey LED Color indicates no lit LED.

33

VersiCharge™ AC Electric vehicle charging station

«
...
30
31
32
33
34
...
»

Summary of Contents for VersiCharge AC





















































Reviews:

No comments

Related manuals for VersiCharge AC

Brand: Zell Pages: 33

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: BAC Pages: 10

Brand: Baby’s Journey Pages: 2

Brand: Dataradio Pages: 72

Brand: PAC Pages: 4

Brand: PAC Pages: 4

SX-70 SODR-X-TRACTOR

Brand: Pace Pages: 2

Brand: PAC Pages: 8

Brand: PAC Pages: 5

Brand: Paradox Pages: 2

Brand: Tait Pages: 10

Powersaver Dual Flexi

Brand: Sangamo Pages: 2

Brand: Targus Pages: 4

Brand: Targus Pages: 2

Brand: Tarot Pages: 5

Brand: Omron Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands