manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 36

 

ST950 Plus+ User Manual 

 

  

 

ST950 Plus+ User Manual 

Page 36 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

ST950 Plus

+

 CPU Card 

The CPU card for Plus

+

 is common with that used for LV and ELV versions of the ST950. There are 

two variants of the CPU card which differ only in the amount of RAM available on the EFC module. 
For Plus

+

, only the 128M RAM variant is appropriate. 

3.8.1

 

General 

The CPU Card controls the system. It holds the controller configuration and performs the function 
of configuration, control and management. The primary external data interfaces are shown in 
Figure 19 and detailed in Table 4. 

One serial phase bus and two GSPI bus connectors are available on 3 separate RJ45 sockets on the 
rear of the CPU Card. The fourth RJ45 socket is reserved for a future GSPI Manual Panel and is 
blanked off and should not be used. 

The RJ45 socket marked “LSLS” on the 

ST950 CPU Card is connected to the first position CTB. 

The two GSPI interface RJ45 sockets are identical and both marked “SIO”. 

The first, marked GSPI 1 

is connected to the first position CTB. The second can be used for other GSPI peripherals e.g. IO 
cards and/or Intelligent Detector Backplanes.   

        

Front Serial 

Phase Bus

(LSLS)

Parellel Phase 

Bus

Status LEDs

Level 3

Pushbutton

USB Master

USB Device

RS232 

Handset

Rear Serial 
Phase Bus
(LSLS)

GSPI 1

GSPI 2

GSPI Manual 
Panel (future)

Cabinet SiGs (top) 
Aux RS232 (bot)

USB Master

Modem pwr (top) 
Modem RS232 (bot)

Ethernet

LGG module

Power Supply
LPU + HPU 
Relays

Front

Rear

 

Figure 18 

–

 ST950 Plus

+

 CPU Card (front and rear views) 

 

Figure 18 shows the CPU Cards interfaces on the front and rear in the orientation when installed 
in the logic rack (but without cables for clarity) 

The significant part positions, of the ST950 CPU Card are identified in Figure 19 below and detailed 
in Table 4. 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands