Siemens ST950 User Manual Download Page 3

Page: 3 / 178

ST950 Plus+ User Manual

Page 3 of 176

667/HE/53000/000

Issue 2

Unrestricted

Re-Commissioning the Junction

When re-commissioning signals, the following sequence is recommended to ensure that the correct
signal start-up sequence is followed:

•

Switch OFF the controller at the main switch

•

Switch ON the lamps at the Manual Panel on/off switch

•

Switch ON the controller at the main switch

More specific safety information is given in the text of the handbook, where it relates to specific
activities or situations.

RJ45 Connections

There are various RJ45 connectors used to connect to peripheral cards within the ST950 family of
controllers. Most are

not

Ethernet ports and should not be connected to other equipment, including

PCs.

To isolate the equipment, the Master Switch must be

in the “Off” position.

Removal of the Electricity Board Fuse or Switching the Controller switch or the Manual Panel Signals

On/Off switch to “Off” does not guarantee isolation of the equipment.

Equipment Compatibility

Do not connect any device that has not been specifically designed or evaluated for compatibility with
the ST950 Plus

system. If in doubt, contact Siemens Mobility Limited for further information.

ST950 Plus

compatible equipment such as Helios Plus

traffic signals, near-side pedestrian signals and

Plus

LED regulatory signs are all clearly marked “

Plus

”. If equipment is not marked “

Plus

” then

additional care should be taken to ensure that it is suitable for use in a Plus

system.

Summary of Contents for ST950



















































































































































































Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands

Siemens ST950, User Manual

Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands