Siemens ST950 User Manual Download Page 120

Page: 120 / 178

ST950 Plus+ User Manual

Page 120 of 176

667/HE/53000/000

Issue 2

Unrestricted

Card partially in container Card fully in container

•

Close the container and rotate locking ring. The fitted card should appear as shown

below.



Card in container

–

unlocked

✓

Card in container - locked

•

Re-connect connectors and power up the controller.

If a Licence Smart Card is already fitted to the controller then the licence is installed using the
Licence Manager to transfer the licence from the Smart Card used for distribution to the Smart
Card fitted to the controller.

Licence Manager

The Licence Manager can be used to:

•

View licences installed on the controller

•

Transfer a licence to the controller

•

Transfer a licence off the controller

The Licence Manager is found on the web page:

Status and Configuration → System → Settings → Licence System → Manager

To view the licence information, press the 'Read Licences' button.

Summary of Contents for ST950



















































































































































































Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands

Siemens ST950, User Manual

Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands