manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 106

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 106 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

9.

 

The armouring must fan out to 90 degrees with a 30mm diameter to be clamped properly. 
See

 

Figure 58. Strip back outer sheath of cable exposing the correct length of armouring 

to be bent down to achieve this. 

10.

 

Check the inner cable cores can pass through the holes in the top clamp. If the holes are 
too  small,  then  replace  the  top  clamp  with  the  larger  22mm  diameter  option 
(667/2/53017/001). 

11.

 

Using pliers bend armouring out to 90 degrees.

 

See

 

Figure 58 

 

 

12.

 

Repeat for the next cable (up to 4 cables per compression seal).  

 

 

Compression Seal Blocks

 

1 off compression seal block  is provided directly under the master switch panel for mains, 

communications  cable  etc.  In  addition,  there  are  another  3  seal  blocks  provided  (12  cable 

entries for street cables), see Figure 44. If more cable entries are required use the Plus+ cabinet 

seal expansion kit 

–

 Extra 8 Cables - 667/1/53065/008. 

 

13.

 

Replace the top clamp and nuts. 

 

 

14.

 

 Tighten down the nuts on the top clamp. Tighten each nut a little at a time so that the 
force is distributed evenly across the plate. This will minimise any side loads from being 
applied to the top clamp. Tighten until the bottom clamp touches the base plate. 

15.

 

Terminate the cables in the cabinet. 

16.

 

Replace the stool door. 

 

Earth Connection 

An earth connection is made by sandwiching the cable armouring between the top and bottom clamps. 
It is important that the clamping force is applied evenly across the clamp plates so please make sure 
that cable armouring does not overlap between cables.    

 

Grease on studs

 

There should be some grease on each stud, please make sure it is there. If there is no grease then it is very 
likely that the nut could seize making it unremovable in the future. If there is no grease then please apply 
either carbon grease or copper grease to the stud. 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands