manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 69

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 69 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

3.17.2

 

Signals On/Off Switch 

The lamp supply to the phase switch cards is removed immediately OFF is selected on the SIGNALS 
OFF/ON switch, extinguishing the signals. 

 

 

Safe Traffic Conditions

 

Care should be taken to ensure safe traffic conditions before operating the switch. 

 

With  the  OFF  position  selected,  normal  microprocessor  control  operations  continue,  and  the 
phase selections being implemented can be observed on the Lamp Switch indicators.  

 

 

Isolation of On Street Equipment 

Switching the Manual Panel Signals On/Off switch to “Off” does not 

provide isolation of the 

equipment. 

 

When the switch is returned to the ON position, the signals turn on as per the configured switch 
on sequence. 

3.17.3

 

Lamp Test Button 

A button on the Manual Panel enables the indicators on the panel, including the Cabinet Alarm 
Lamp, to be checked. 

When the button is pressed, all LEDs on the Manual Panel should light. The lamp test is carried out 
under software control, and although correct results indicate that the processor is communicating 
with the Manual Panel, it does not guarantee that no faults are present. 

3.17.4

 

Mode Select Buttons (Manual, VA, Fixed Time, Etc) 

These keys select the required mode for the controller. 

The controller can be configured so that manual mode is only available if a handset is plugged in. 
An alternative configuration is such that manual mode may only be selected following a specific 
handset command (see MND command). 

 

3.17.5

 

Stage Select Buttons (All Red, 1 - 7) 

With Manual mode selected (Manual LED lit), the keys ALL RED, 1 - 7 select the configured stage 
(or  combination  of  stages)  provided  the  AWAITING  COMMAND  indicator  is  illuminated  and  a 
prohibited stage move is not requested. 

 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands