manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 127

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 127 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

 

 

The time mode, date and time can be set from the web page: 

Status and Configuration → Controller → Clocks

 

The user should configure the controller clocks as required - refer to the Time section in the ST950 
Facilities Handbook 667/HB/46000/001 and then set the time and date as follows: 

•

 

Enter the current date in the 'Set Date' box using one of the accepted formats 

•

 

Enter the time to be set in the 'Set System Time' and / or 'Set Controller Time' (depending on 

the clock system required) in one of the accepted formats 

•

 

Press the 'Save' button at the precise time set. 

 

 

System Time : Stratos Connection

 

It is not necessary to set the System time when the profile is set to 

Stratos

.

 

 

 

System Time : Stratos Connection

 

It is not necessary to set the System time when the profile is set to 

Stratos

.

 

 

 

System Time : NTP

 

If NTP is used, the time may not be the actual time but that used by the system (In-Station 

time)

 

 

 

System Time : CLF Plans

 

If CLF plans are to be used it is important that the clock be set accurately to ensure that the 

plans operate as expected. 

 

The Handset  can also  be used to set  the Real Time Clock  using  Level 3 access and the 'TOD=' 
command, for example: 

'TOD=21AUG13' to set the Date and 

'TOD=10:36:00' to set the time 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands