manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 144

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 144 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

9.4.6

 

Replacement of CPU Card 

In case of failure, the CPU Card should be replaced. The Licence card and Heart of the controller 
(SD card) should be moved to the new card to preserve the junction configuration and facilities. 

 

Replacement CPU Card

 

Only replace a CPU card with a compatible variant: 667/1/46010/101 

 

 

Replacement CPU Card : IP Configuration

 

Before  re-connecting  the  Ethernet  connector  ensure  that  the  new  CPU  card  has  the  IP 

configuration set correctly. Failure to do this may result in network disruption that can affect 

other network devices. 

 

When replacing a CPU card, it is possible to clone the running system, from the CPU card being 
replaced, onto the new CPU card, using the Heart of the Controller. The steps to perform this are 
described in this section. 

 

 

Cloning and Restoration of a CPU Heart

 

When restoration from Heart is being performed, to clone a system onto a replacement CPU 

card, it is important that the Ethernet cable, if used, is not connected to the replacement CPU 

card, until the restore from Heart operation is complete. This is to avoid conflicting network  

issues due to prior and incompatible network configurations. 

 

Move Heart to new CPU card 

Take the CPU card being replaced and remove the SD card from the slot marked "HEART". Insert 
this SD card into the replacement CPU card. To insert a card, align it with the socket with the 
contacts facing PCB and closest to the socket, slide it into the socket and apply slight pressure until 

it ‘clicks’. The card is now located correctly. The photos below show the correct orientation for the 

card. 

Note: It is important that the ca

rd is not write protected. The ‘lock’ switch must be in the position 

shown in the diagram below: 

 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands