manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 99

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 99 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

5 

U

SER 

I

NTERFACE

 

The user interface is fully described in the User Interface Guide 667/HU/46000/000. This section 
gives a brief overview of the user interface. Information related to Plus+ operations is provided in 
the relevant sections of this document. 

 

Connection 

There are several ways for the user to connect to the controller: 

•

 

RS232 Handset Port 

•

 

USB Handset Port 

•

 

Wi-Fi 

•

 

Ethernet Port 

A driver needs to be installed in order to use the USB Handset port. A suitable driver for Windows 
is provided by the controller and can be installed on connection to the controller. 

 

Types of User Interface 

There are three styles of user interface. 

5.2.1

 

Web Browser 

The controller web interface provides full control and monitoring of the controller. It is available 
over the USB handset and network connections. 

 

 

 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands