manualshive.com logo in svg

Siemens ST950, User Manual

Share
Download
Siemens ST950 User Manual Download Page 135

 

ST950 Plus+ User Manual 

 

  

 

 

ST950 Plus+ User Manual 

Page 135 of 176 

667/HE/53000/000   

Issue 2 

Unrestricted 

 

 

The following checks should be carried out before leaving the site; 

Check the cabinet door seals are intact and in the correct positions. Replace as necessary ensuring 
the surface is clean before fitting. 

If appropriate (when using a Standard Controller Stool) inspect the cabinet base seal. If damaged, 
the affected area should be filled with sand and re-sealed. For details see the Controller  Stool 
Installation Method Statement (667/CC/53060/000). 

 

Routine Setup Check 

Check that the real time clock is set correctly. 

A true measurement of the accuracy of the real time clock can only be gained if the clock with 
which it is compared has been accurately set up.  

It is essential that the time be compared with an adjacent controller using a clock that has been 
synchronised to that controller within the last 30 minutes.  

 

Other Maintenance Operations 

The following maintenance procedures may also be required and are described elsewhere in this 
document. 

•

 

RTC battery replacement - see section 6.9.2 

•

 

Addition & removal of licences - see section 6.9.7 

•

 

Loading new IC4 configuration - see section 6.9.3 

•

 

Loading of new Plus

+

 Site Layout Design 

–

 see section 6.9.4 

•

 

Update of firmware - see section 6.9.6 

•

 

Export of site information - see section 6.9.15 

 

 

Summary of Contents for ST950



















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands