Siemens ST950 User Manual Download Page 38

Page: 38 / 178

ST950 Plus+ User Manual

Page 38 of 176

667/HE/53000/000

Issue 2

Unrestricted

Description

Connector

Serial Phase bus to CTB

RJ45

GSPI Bus to CTB

RJ45

GSPI Bus to I/O Cards (SIO) or other GSPI
peripherals

RJ45

GSPI Manual Panel (PANEL) [Future Use]

RJ45

Cabinet Signals (Top)
Auxiliary RS232 Connection (Bottom)

Double stacked 10 way IDC
Refer to Table 2 for pinout

Rear USB Host Port

USB Type A

10/100 Ethernet (ETH)

RJ45

Modem Power / Ancillary I/O (Top)
RS232 Modem Connection (Bottom)

Double stacked 10 way IDC
Refer to Table 3 for pinout

Battery Backup module connector

6 way Molex Mini-Fit Jr.

Power Supply Connector (24VDC PSU)

12 way Molex Mini-Fit Jr.

Serial Phase bus (

not used for Plus

)

10 way IDC

Parallel Phase Bus (

not used for Plus

)

34 way IDC

Front USB Host Port

USB Type A

USB Handset Port

USB Type B

RS232 Handset Port

25 way D type

–

Female

Parallel Manual Panel Port

34 way IDC

Table 4

–

Connector Functions and Types

3.8.2

Processor Status LEDs

Overview

The LEDs located on the front of the CPU Card and immediately behind the handset port are used
to convey controller operational states and other information to the user.

Front of the CPU Card

The nine LEDs on the front of the CPU Card as shown below (viewed from the front).

The function of each LED is described below;

–

Watchdog (red)

Illuminated when the Primary CPU is not running, or an internal fault has been detected.

–

Heartbeat (green)

WD HB SE SD FF PRG SYS COM BSY

Summary of Contents for ST950



















































































































































































Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands

Siemens ST950, User Manual

Search results

Summary of Contents for ST950

Reviews:

Brands by name

Popular brands