manualshive.com logo in svg

Siemens SITRANS F M MAG 8000, Operating Manual, Page: 41 / 64

Share
Download
Siemens SITRANS F M MAG 8000 Operating Manual Download Page 41

MAG 8000 & MAG 8000 CT

41

SFIDK.PS.026.D9.02

7. Service

7.1.1 Faults codes

(continued)

Faults

Alarm description

Alarm reasons

codes

Warning

Indication of wrong setting or application issues

5

Low power

Battery voltage is below 2 volts or battery capacity is below the low
power % limit (set as customer parameter FT206).  When low
voltage is detected, flow measurement and communication will stop,
but the display will remain active as long as some power is
available. The alarm remains active until the fault condition is
resolved.
-> Check the calculated battery capacity (FT510) versus the
battery alarm limit (FT206) and replace batteries as necessary.

6

Flow overflow

Flow rate through the meter is 25% above Qn (Q3) and the meter
stops counting at 125% flow. The alarm remains active until the
fault condition is resolved.
-> Check the sizing of the meter for the current installation.

7 & 8

Pulse 1 & 2 overflow

The pulse rate is higher than the pulse output can deliver.
Reminder: the 

basic version 

is limited to 50 Hz maximum; the

advanced version

 is limited to 100 Hz maximum. The alarm

remains active until the output pulse rate drops below the maxi-
mum pulse rate.
-> Change volume per pulse to a higher value - see section 8
“Technical data“ for pulse selection.

9

Consumption  warning

The data logged consumption on totalizer 1 has exceed the too low
or too high consumption limit. The alarm remains active until it is
manually reset by FT209.
-> Check data logger values and consumption limit.

L

Leakage

The lowest flow rate or volume during leakage period has

(Advanced version

exceeded the leakage detection settings. The alarm is active until

only)

it is manually reset by FT208. An alarm reset (similar to leakage
period reset FT820) will reset information for the selected function.
-> Check setting and pipe installation.

E

Empty pipe

The measured electrode impedance is above the empty pipe level
(FT540 & FT541 & FT334). The alarm remains active until the fault
condition is resolved.
-> Make sure the sensor is filled with water.

C

High  conductivity

The electrode impedance is below the low media impedance
(FT542) - meaning the water has a high conductivity. The alarm is
active until the resistance in the water is above the low media
alarm limit.

d

High flow rate

The flow rate is greater than the flow alarm limit (FT553).
The alarm remains active until the flow rate drops below the flow
alarm limit.

Warning faults cover operating conditions where settings or monitored values exceed configured
limits.
Some of the warnings require a manual reset before they are removed from the alarm list.

Note

A reset of the fault log (FT204) also resets all alarms. Once reset, only active alarms become
visible again.

Summary of Contents for SITRANS F M MAG 8000

































































Reviews:

No comments