Siemens SIRIUS Series System Manual Download Page 64

Page: 64 / 182

Installation/Removal

8.1 Installing the SIRIUS 3RA6 compact starter and AS-i mounting module

SIRIUS 3RA6 Compact Starter

System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

8.1.3

Installing the compact starter on a SIRIUS infeed system for 3RA6

Requirements

●

The SIRIUS infeed system for 3RA6 must be correctly installed. For additional information

on installing the infeed system, please refer to "SIRIUS infeed system for 3RA6

(Page 95)".

●

The compact starter must be switched off (actuator set to OFF position).

CAUTION

Compact starter material damage!
There is a risk of the compact starter getting damaged if it is switched on (i.e. actuator in

READY position) when you install it on the infeed system for 3RA6.

Make sure that the compact starter's actuator is set to the OFF position before you

install the compact starter on the infeed system for 3RA6.

Procedure

Step

Instructions

Image

Attach the compact starter to the front of

the infeed system for 3RA6.

Push the compact starter straight onto

the infeed system for 3RA6 until you

hear it engage.

Summary of Contents for SIRIUS Series























































































































































































Search results

Summary of Contents for SIRIUS Series

Reviews:

Related manuals for SIRIUS Series

Brands by name

Popular brands

Siemens SIRIUS Series, System Manual

Search results

Summary of Contents for SIRIUS Series

Reviews:

Related manuals for SIRIUS Series

Brands by name

Popular brands