Siemens SIRIUS Series System Manual Download Page 177

Page: 177 / 182

SIRIUS 3RA6 Compact Starter
System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

175

Glossary

3-phase busbar

The 3-phase busbar enables several compact starters to be fed using a single infeed

terminal.

8US busbar adapter

The 8US busbar adapter enables the compact starter to be mechanically fastened and

electrically connected to a busbar system.

Adapter for screw fastening

The adapters for screw fastening enable you to install the compact starter on a level surface.

AS-Interface

The actuator sensor interface (AS-Interface) is a modular networking system for sensors and

actuators at the lowest field level.

Auxiliary switch block for compact starter

Optional auxiliary switch block in the following versions: 2 NO contacts, 2 NC contacts or

1 NO c 1 NC contact

Control kit

Tool for closing the main contacts manually by means of the actuator

Door-coupling rotary operating mechanism

Door-coupling rotary operating mechanisms enable compact starters to be operated with the

control cabinet doors closed.

Infeed system for 3RA6

The infeed system for 3RA6 enables several compact starters to be fed using a modular

infeed system with permanent wiring.

Summary of Contents for SIRIUS Series























































































































































































Search results

Summary of Contents for SIRIUS Series

Reviews:

Related manuals for SIRIUS Series

Brands by name

Popular brands

Siemens SIRIUS Series, System Manual

Search results

Summary of Contents for SIRIUS Series

Reviews:

Related manuals for SIRIUS Series

Brands by name

Popular brands