Siemens SIRIUS Series System Manual Download Page 129

Page: 129 / 182

Accessories

12.6 Terminal for Type E combination motor controller, UL 508

SIRIUS 3RA6 Compact Starter
System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

127

12.6

Terminal for Type E combination motor controller, UL 508

12.6.1

Installing the terminal for a Type E self-protected combination motor controller

(UL 508)

According to UL 508 (Type E), line-side clearances of 1 and 2 inches are required for Type E

combination motor controllers. If parallel wiring is used for the compact starter, the terminal

for the self-protected combination motor controller (Type E) (3RV1928-1H) should be used.

Note
According to C22.2-14, terminal blocks are not required for installation in accordance with

CSA requirements.

Note
Supply possibilities in accordance with UL 508 (Type E) are still available when compact

starters are installed with a 3-phase busbar and the infeed system for 3RA6. For additional

information, please refer to "Infeed in accordance with UL 508 (Type E) (Page 36)".

Procedure

Step

Instructions

Image

Attach the terminal to the compact

starter's main conductor terminal from

the top.

Screw the screw terminals tight.

Summary of Contents for SIRIUS Series























































































































































































Search results

Summary of Contents for SIRIUS Series

Reviews:

Related manuals for SIRIUS Series

Brands by name

Popular brands

Siemens SIRIUS Series, System Manual

Search results

Summary of Contents for SIRIUS Series

Reviews:

Related manuals for SIRIUS Series

Brands by name

Popular brands