Siemens SIRIUS Series System Manual Download Page 13

Page: 13 / 182

SIRIUS 3RA6 Compact Starter
System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

Product-specific information

2.1

Standards/Regulations/Approvals

Standards

The 3RA6 compact starter conforms to the following standards:
●

IEC / EN 60947-6-2

●

UL 508 Type E

●

CSA C22.2 No. 14 Type E

Approvals/Test reports

UL and CSA approval was being sought at the time of going to press. Once approval has

been obtained, the compact starter will be marked with the symbols and .

Note

- Marking

Any compact starter that does not bear the marking is not intended for the US market.

Confirmation of approvals, test certificates and characteristic curves is available via the

Internet:
www.siemens.de/lowvoltage/technical-assistance

Compact starter degree of protection

The compact starter's degree of protection is IP20. In the terminal area it features

IP00 degree of protection.

Infeed system degree of protection for 3RA6

The infeed system for the 3RA6 features IP20 degree of protection. In the terminal area it

features IP00 degree of protection.

Isolating features

The requirements of IEC / EN 60947-3 have been met in respect of the isolating features.

Summary of Contents for SIRIUS Series























































































































































































Search results

Summary of Contents for SIRIUS Series

Reviews:

Related manuals for SIRIUS Series

Brands by name

Popular brands

Siemens SIRIUS Series, System Manual

Search results

Summary of Contents for SIRIUS Series

Reviews:

Related manuals for SIRIUS Series

Brands by name

Popular brands