Siemens SIRIUS Series System Manual Download Page 126

Page: 126 / 182

Accessories

12.5 8US busbar adapter

SIRIUS 3RA6 Compact Starter

124

System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

Step

Instructions

Image

Push the mounting lug into the adapter

from the bottom.

Snap the compact starter onto the DIN

rail, connecting it to the busbar adapter.

Insert each of the screws through the

relevant holes in the mounting lug and

screw the compact starter onto the

busbar adapter.

Connect the wiring from the busbar

adapter to the compact starter's main

conductor terminal block.

Mount the busbar adapter on the

busbars from the top.

Procedure for 3RA62 compact starter reversing starter

If you are mounting a reversing starter on the 8US busbar adapter, the reversing starter's

width means that it will need to be mounted on a device holder (8US1250-1AA10) as well.

Step

Instructions

Image

Position the device holder next to

the 8US busbar adapter.

Press the 2 connecting plugs into the

relevant openings from behind to

connect the device holder to the

8US busbar adapter.

Press the button on the top side of the

busbar adapter and device holder to

release the holders. The holders should

flip out from the front of the busbar

adapter and device holder.

Summary of Contents for SIRIUS Series























































































































































































Search results

Summary of Contents for SIRIUS Series

Reviews:

Siemens SIRIUS Series, System Manual, Page: 126 / 182

Search results

Summary of Contents for SIRIUS Series

Reviews: