Siemens SIRIUS Series System Manual Download Page 16

Page: 16 / 182

System description

3.1 System overview

SIRIUS 3RA6 Compact Starter

System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

Accessories

As well as providing details of the compact starter and AS-i mounting module, this document

also describes the following accessories:

Table 3-2

Accessories for the 3RA6 compact starter

Accessories

Description

Chapter

Auxiliary switch block for

compact starter

Optional auxiliary switch block in

the following versions: 2 NO

contacts, 2 NC contacts or

1 NO c 1 NC contact

External auxiliary switch block

(Page 91)

Control kit

Tool for closing the main

contacts manually by means of

the actuator

Control kit (Page 89)

Adapter for screw fastening the

compact starter

The adapters for screw

fastening enable you to install

the compact starter on a level

surface (screw fastening).

Installing the compact starter on

a level surface (screw fastening)

(Page 60)

Terminals for

"Combination Controller Type E"

The terminals conform to the

creepages and clearances

stipulated by UL 508 (Type E).

Terminal for Type E

combination motor controller,

UL 508 (Page 127)

Infeed system for 3RA6

The infeed system for 3RA6 is a

modular infeed system with an

optional PE system. The

permanent wiring means that

compact starters can be

mounted quickly and easily.

SIRIUS infeed system for 3RA6

(Page 95)

3-phase busbar

The 3-phase busbar enables

several compact starters to be

fed using a single infeed

terminal.

3-phase busbar (Page 117)

8US busbar adapter

The 8US busbar adapter

enables the compact starter to

be mechanically fastened and

electrically connected to a

busbar system.

8US busbar adapter

(Page 121)

Door-coupling rotary operating

mechanism

Door-coupling rotary operating

mechanisms enable compact

starters to be operated with the

control cabinet doors closed.

Door-coupling rotary operating

mechanism (Page 129)

Summary of Contents for SIRIUS Series























































































































































































Search results

Summary of Contents for SIRIUS Series

Reviews:

Siemens SIRIUS Series, System Manual, Page: 16 / 182

Search results

Summary of Contents for SIRIUS Series

Reviews: