Siemens SIRIUS Series System Manual Download Page 131

Page: 131 / 182

Accessories

12.7 Door-coupling rotary operating mechanism

SIRIUS 3RA6 Compact Starter
System Manual, 02/2008, GWA 4NEB 560 0601-02 DS 02

129

12.7

Door-coupling rotary operating mechanism

12.7.1

Description of the hardware

Door-coupling rotary operating mechanisms consist of a lockable rotary operating

mechanism with a removable door coupling, an extension shaft and a connection piece that

joins onto the switch mechanism. There are two basic versions available:
●

Door-coupling rotary operating mechanism for standard applications

(order number: 3RV1926-0B)

●

Door-coupling rotary operating mechanism for EMERGENCY OFF applications

(black/red actuator) (order number: 3RV1926-0C)

Both versions have been designed to provide IP65 degree of protection and can be locked in

the OFF position using up to 3 padlocks.

12.7.2

Installing the door-coupling rotary operating mechanism

min. 16 mm

max. 20 mm

Figure 12-9 Installing the door-coupling rotary operating mechanism

Remember to observe the mechanical coding of the connecting rod!

Summary of Contents for SIRIUS Series























































































































































































Search results

Summary of Contents for SIRIUS Series

Reviews:

Siemens SIRIUS Series, System Manual, Page: 131 / 182

Search results

Summary of Contents for SIRIUS Series

Reviews: