Siemens Simatic S7-1500 Function Manual Download Page 241

Page: 241 / 402

Instructions

11.1 S7-1500 Motion Control V2

S7-1500 Motion Control V13 Update 3
Function Manual, 07/2014, A5E03879256-AC

241

Parameters

The following table shows the parameters of the "MC_Home" Motion Control instruction:

Parameter

Declaration Data type

Default value Description

Axis

InOut

TO_Axis

Technology object

Execute

INPUT

BOOL

FALSE

Start of the job with a positive edge

Position

INPUT

LREAL

0.0

The specified value is used according to the selected

"Mode".

Mode

INPUT

INT

Operating mode
0

Direct homing (absolute)
The current position of the technology ob-

ject is set to the value of parameter

"Position".

Direct homing (relative)
The current position of the technology ob-

ject is shifted by the value of parameter

"Position".

Passive homing

(without reset)
Functions like "Mode" 8, with the difference

that the "homed" status is not reset when

the function is enabled.

Active homing
The TO positioning axis/synchronous axis

performs a homing movement according to

the configuration.

After the completion of the movement, the

axis is positioned at the value of the

"Position" parameter.

Reserved

Active homing

("Position" parameter has no effect)
The TO positioning axis/synchronous axis

performs a homing movement according to

the configuration.

After completion of the movement, the axis

is positioned at the home position config-

ured under "Technology object > Configura-

tion > Extended parameters > Homing >

Active homing".
(<TO>.Homing.HomePosition)

Absolute encoder adjustment (relative)
The current position is shifted by the value

of the parameter "Position".
The calculated absolute value offset is

stored retentively in the CPU.
(<TO>.StatusSensor[n].

AbsEncoderOffset)

Summary of Contents for Simatic S7-1500



















































































































































































































































































































































































































Search results

Summary of Contents for Simatic S7-1500

Reviews:

Related manuals for Simatic S7-1500

Brands by name

Popular brands

Siemens Simatic S7-1500, Function Manual

Search results

Summary of Contents for Simatic S7-1500

Reviews:

Related manuals for Simatic S7-1500

Brands by name

Popular brands