Siemens SIMATIC NET SCALANCE W748-1 Page 54 Operating Instructions Manual Download

Page: 54 / 78

Connecting up

6.4 Antenna connectors

SCALANCE W788-x / W748-1

Operating Instructions, 03/2022, A5E03678333-17

R-SMA for degree of protection IP30

The variants of the SCALANCE W7x8 RJ45 have antenna sockets of the type R-SMA:
•

Variants with an IWLAN interface (W7x8-1) have 3 antenna sockets on the top of the

device.

•

Variants with two IWLAN interfaces (W788-2) have 6 antenna sockets, 3 on the top

and 3 on the underside of the device.

NOTICE
R-SMA antenna connector

When securing antennas to the device, only the screw cap (see figure) of the antenna

can be rotated. Rotating the entire antenna could damage the R-SMA connector of the

device.

①

R1A1

②

R1A2

③

R1A3

④

R2A1

⑤

R2A2

⑥

R2A3

Figure 6-1 Antenna connector IP30

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands