Siemens SIMATIC NET SCALANCE W748-1 Page 18 Operating Instructions Manual Download

Page: 18 / 78

Security recommendations

SCALANCE W788-x / W748-1

Operating Instructions, 03/2022, A5E03678333-17

The following is a list of all available Layer 2 services through which the device can be

accessed.
The table includes the following columns:
•

Layer 2 service

The Layer 2 services that the device supports

•

Default status

The default status of the service (open or closed).

•

Service configurable

Indicates whether the service can be configured via WBM / CLI.

Layer 2 service

Default
status

Service

configurable

DCP

Open

✓

LLDP

Open

✓

RSTP

Open

✓

iPRP

Open

✓

MSTP

Closed

✓

SIMATIC NET TIME

Closed

✓

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands