Siemens SIMATIC NET SCALANCE W748-1 Operating Instructions Manual Download Page 26

Page: 26 / 78

Description of the device

4.4 Accessories

SCALANCE W788-x / W748-1

Operating Instructions, 03/2022, A5E03678333-17

For railway applications, the following connecting cable is available, scope of delivery 1

unit:

Length

Article number

1 m

6XV1875-5VH10

4.4.5.2

Lightning protection

Component

Description

Article number

LP798-1N

Lighting protector with N/N

female/female connector with gas

discharge technology

6GK5798-2LP00-2AA6

LP798-2N

Lighting protector with N/N

female/female connector with quarter

wave technology

6GK5798-2LP10-2AA6

4.4.5.3

Terminating resistor

Component

Description

Article number

TI795-1N

Electrical connection
N-Connect, male

6GK5795-1TN00-1AA0

TI795-1R

Electrical connection
RSMA-Connect, male

6GK5795-1TR10-0AA6

4.4.5.4

Cabinet feedthrough

Component

Description

Article number

IE M12 PANEL

FEEDTHROUGH 4 x 2

Cabinet feedthrough for conversion from

M12 connector technology (X-coded,

IP65/67) to RJ-45 connector technology (X-

coded, IP20)
pack of 5

6GK1901-0DM40-2AA5

N-Connect/N-Connect

female/Female panel

feedthrough

Panel feedthrough for wall thicknesses up

to a maximum of 4.5 mm, two N-Connect

female connectors.

6GK5798-2PP00-2AA6

N-Connect/SMA-

Connect

female/Female panel

feedthrough

Panel feedthrough for wall thicknesses up

to a maximum of 5.5 mm, two N-

Connect/SMA female connectors.

6GK5798-0PT00-2AA6

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual, Page: 26 / 78

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews: