Siemens SIMATIC NET SCALANCE W748-1 Page 29 Operating Instructions Manual Download

Page: 29 / 78

Description of the device

4.5 LED display

SCALANCE W788-x / W748-1
Operating Instructions, 03/2022, A5E03678333-17

4.5

LED display

Information on operating status and data transfer

On the front of the housing, several LEDs provide information on the operating status of

the SCALANCE W7x8:

LEDs with RJ-45 variants

LEDs with M12 variants

Note

The "R2" LED only exists on devices with two IWLAN interfaces.

LED

Color

Meaning

Off

Power supply L1 too low.

Green

Power supply L1 is applied.

Off

Power supply L2 too low.

Green

Power supply L2 is applied.

PoE

Off

The device is not supplied using PoE.

Green

The device is supplied using PoE.

Off

There is no connection over the Ethernet port P1.

Green

There is a connection over the Ethernet port P1 (link).

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands