manualshive.com logo in svg

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual, Page: 56 / 78

Share
Download
Siemens SIMATIC NET SCALANCE W748-1 Operating Instructions Manual Download Page 56

Connecting up 

 

6.4 Antenna connectors 

 

SCALANCE W788-x / W748-1 

56

 

Operating Instructions, 03/2022, A5E03678333-17 

 

Note 
Terminating resistor 

Each WLAN interface has three antenna connectors. Connectors that are not used must 

have a terminating resistor fitted, see Accessories (Page 22). 
The antennas R1A1 and R2A1 must always be connected as soon as the associated 

WLAN Interface is turned on. if no antenna is connected, the relevant interface must also 

be disabled for RX and TX. Otherwise, there may be transmission disruptions. 
You will find information on the configuration of the antennas in the following 

documents: 
•

 

SCALANCE W7x8 

SCALANCE W700 configuration manual, section "Configuring antennas" 

 

 

①

 

R1A1 

②

 

R1A2 

③

 

R1A3 

④

 

R2A1 

⑤

 

R2A2 

⑥

 

R2A3 

Figure 6-3  Antenna connector IP65 

 

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Reviews:

No comments