Siemens SIMATIC NET SCALANCE W748-1 Page 38 Operating Instructions Manual Download

Page: 38 / 78

Installation and removal

5.1 Safety notices for installation

SCALANCE W788-x / W748-1

Operating Instructions, 03/2022, A5E03678333-17

WARNING

The device is intended for indoor use only.

Safety notices on use in hazardous areas

General safety notices relating to protection against explosion

WARNING

When used in hazardous environments corresponding to Class I, Division 2 or Class I,

Zone 2, the device must be installed in a cabinet or a suitable enclosure.

WARNING

EXPLOSION HAZARD

Replacing components may impair suitability for Class 1, Division 2 or Zone 2.

WARNING

The device may only be operated in an environment of contamination class 1 or 2 (see

EN/IEC 60664-1, GB/T 16935.1).

Notes for use in hazardous locations according to ATEX, IECEx, UKEX and CCC Ex

If you use the device under ATEX, IECEx, UKEX or CCC Ex conditions you must also keep

to the following safety instructions in addition to the general safety instructions for

protection against explosion:

WARNING

To comply with EU Directive 2014/34 EU (ATEX 114), UK-Regulation SI 2016/1107 or

the conditions of IECEx or CCC-Ex, the housing or cabinet must meet the requirements

of at least IP54 (according to EN/IEC 60529, GB/T 4208) in compliance with EN

IEC/IEC 60079-7, GB 3836.8.

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands