Siemens SIMATIC NET SCALANCE W748-1 Page 9 Operating Instructions Manual Download

Page: 9 / 78

SCALANCE W788-x / W748-1
Operating Instructions, 03/2022, A5E03678333-17

Safety notices

CAUTION

To prevent injury and damage, read the manual before using the device.

Read the safety notices

Note the following safety notices. These relate to the entire working life of the device.
You should also read the safety notices relating to handling in the individual sections,

particularly in the sections "Installation" and "Connecting up".

WARNING

Hot surfaces

Electric devices have hot surfaces. Do not touch these surfaces. They could cause

severe burns.
•

Allow the device to cool down before starting any work on it.

WARNING

EXPLOSION HAZARD

Do not open the device when the supply voltage is turned on.

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands