Siemens SIMATIC NET SCALANCE W748-1 Page 62 Operating Instructions Manual Download

Page: 62 / 78

Troubleshooting

8.1 Device configuration with PRESET-PLUG

SCALANCE W788-x / W748-1

Operating Instructions, 03/2022, A5E03678333-17

Procedure

Start the remote configuration using Telnet (CLI) and log on with a user with the

"admin" role.

Switch to the global configuration mode with the command "configure terminal".

You change to the PLUG configuration mode with the "plug" command.

Create the PRESET-PLUG with the "presetplug" command.

The firmware version of the device and the current device configuration incl. user

accounts and certificates are stored on the PLUG and the PLUG is then write

protected.

Turn off the power to the device.

Remove the PRESET-PLUG.

Start the device either with a new PLUG inserted or with the internal configuration.

Procedure for installation with the aid of the PRESET-PLUG

Turn off the power to the device.

If it exists, remove the PLUG from the slot. You will find further information on this in

the operating instructions of your device.

Insert the PRESET-PLUG correctly oriented into the slot. The PRESET-PLUG is

correctly inserted when it is completely inside the device and does not jut out of the

slot.

Turn on the power to the device again.

If there is a different firmware version on the device to be installed compared with that

on the PRESET-PLUG, an upgrade/downgrade of the firmware is performed. You can

recognize this by the red F-LED flashing (flashing interval: 2 sec on/0.2 sec. off).

Afterwards the device is restarted and the device configuration incl. users and

certificates on the PRESET-PLUG is transferred to the device.

Wait until the device has fully started up.
The red F-LED is off.

Turn off the power to the device after the installation.

Remove the PRESET-PLUG.

Start the device either with a new PLUG inserted or with the internal configuration.

Note
KEY-PLUG

If you have created the PRESET-PLUG from a KEY-PLUG, for operation with this

configuration, you require an inserted KEY-PLUG.
IN this case before recommissioning the device you need to insert the relevant KEY-

PLUG.

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands