Siemens SIMATIC NET SCALANCE W748-1 Page 44 Operating Instructions Manual Download

Page: 44 / 78

Installation and removal

5.6 Installing on a DIN rail

SCALANCE W788-x / W748-1

Operating Instructions, 03/2022, A5E03678333-17

5.6

Installing on a DIN rail

The SCALANCE W7x8 is suitable for rail mounting on 35 mm DIN EN 50022 rails.

Mounting adapter for DIN rail

Note

The mounting adapter for installation on a DIN rail is not included in the scope of

delivery, see Accessories (Page 23).

The mounting adapter consists of the following parts:
•

1 DIN rail slider

•

1 spring

•

2 screws

Mount the mounting adapter on the rear of the device as shown in the figure below:

Figure 5-4 Fitting the DIN rail slider

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands