manualshive.com logo in svg

Siemens SIMATIC MP 270B, Operating Instructions Manual

Share
Download
Siemens SIMATIC MP 270B Operating Instructions Manual Download Page 93

 

TP 270, OP 270, MP 270B (WinCC flexible) 
Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0 

7-1

 

Prepare and backup project 

7

7.1 

Transfer project to the HMI device 

7.1.1 

Commissioning for the first time 

Introduction 

There is no configuration on the HMI device when commissioning for the first time. In order 

to transfer the necessary project data and the runtime software from the configuration 

computer to the HMI device, proceed as follows, observing the sequence. 

 

 

Notice 
When starting the first time, observe the safety information on reverse poling. 

 

 

Caution 
Always terminate the runtime software before switching off the voltage supply in order to 

prevent loss of data. 
Press the operating element linked to the "StopRuntime" system function in the project to 

stop runtime. Wait until the HMI device displays the loader and then switch off the power 

supply. 

 

 

Note 
During the commissioning phase, it is possible to connect an external USB keyboard or 

mouse via the USB interface. 

 

 

Summary of Contents for SIMATIC MP 270B



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands