Siemens SIMATIC MP 270B Operating Instructions Manual Download Page 50 | Manualshive

Page: 50 / 274

Siemens SIMATIC MP 270B Operating Instructions Manual Download Page 50

Installation and connection

4.3 Connecting the HMI device

TP 270, OP 270, MP 270B (WinCC flexible)

4-12

Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0

4.3.4.2

Connect external keyboard and mouse

Connection configuration

The figure below illustrates how to connect a keyboard or mouse to the HMI device's USB

interface. A keyboard or mouse can be connected and disconnected during normal

operation.

USB

USB standard keyboard

USB standard mouse

Operating unit

Figure 4-4

Connection configuration for external keyboard and mouse

Notice
Connecting a USB distributor (USB hub) to the HMI device's USB interface can cause a

restriction in the functionality of the connected USB devices and the HMI device.
Therefore, the simultaneous or alternating operation of USB devices connected via a USB

hub on the HMI device's USB interface is not approved.
This applies to USB hubs both with and without an internal power supply.

Notice
Use a standard mouse and keyboard with a "USA/International" keyboard layout.

Commercially available USB devices do not normally meet the higher industrial demands

relating to interference resistance and can have negative effects on the HMI device.
The power consumption must not exceed 500 mA with the USB units connected.

See also

Operation with external keyboard/mouse (Page 5-12)

«
...
48
49
50
51
52
...
»

Summary of Contents for SIMATIC MP 270B



















































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands