manualshive.com logo in svg

Siemens SIMATIC MP 270B, Operating Instructions Manual

Share
Download
Siemens SIMATIC MP 270B Operating Instructions Manual Download Page 77

 

Operating system and configuration 

 

6.2 Windows CE Control Panel 

TP 270, OP 270, MP 270B (WinCC flexible) 
Operating Instructions, Edition 03/2004, 6AV6691-1DD01-0AB0 

6-7

 

6.2.6 OP 

"OP" option 

 

The following setting options are provided by the "OP" option in the Control Panel: 

• 

Set brightness 

• 

Set contract (for OP 270 and TP 270 only) 

• 

Calibrate touchscreen (for MP 270B Touch and TP 270 only) 

• 

Display device data 

• 

Backup non-resistant data 

Set brightness 

 

 

Note 
The MP 270B (TFT display) does not support the "Contrast" function. 

 

1.  Open the "Display" tab in the "OP Properties" dialog.  

 

Figure 6-3 

"OP Properties" dialog, "Display" tab 

2.  Change the brightness setting of the screen using the "UP" and "DOWN" buttons in the 

"Brightness" group. 

Summary of Contents for SIMATIC MP 270B



















































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands