Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 90 / 158

Maintaining and servicing your device

7.2 Maintenance intervals

SIMATIC IPC677E

Operating Instructions, 04/2019, A5E45117996-AA

7.2

Maintenance intervals

To maintain high system availability, we recommend the preventative replacement of those

PC components that are subject to wear. The table below indicates the intervals for this

replacement.

Component

Replacement interval:

Hard disk drive

3 years

Fan

3 years

CMOS backup battery

5 years

SSD

Depends on the type of use

The interval for replacement of the flash drives (SSD) depends greatly on the type of use. A specif-

ic interval cannot be given.

Note
All drives are monitored with the SIMATIC DiagBase or SIMATIC DiagMonitor software tools

on the basis of their Smart status.
As soon as the Smart status of the data storage medium goes to "Not OK", a message is

generated in SIMATIC DiagBase or SIMATIC DiagMonitor or also during a system start of

the device. You should then back up your data and replace the drive.

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands