Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 118 / 158

Technical specifications

8.9 Technical specifications of the interfaces

SIMATIC IPC677E

118

Operating Instructions, 04/2019, A5E45117996-AA

Keyboard

USB support

Mouse

USB support

USB

4 × USB 3.1, type A, high current, backward compatible
2 × USB 3.1, type C, high current, backward compatible

Ethernet

3 × Ethernet ports (RJ45), 10/100/1000 Mbp

•

1 x Ethernet 1: Intel® Jacksonville i219-LM; AMT-capable

•

2 x Ethernet 2, 3: Intel® Springville i210-AT

Wake on LAN, Remote Boot and the following Teaming modes are

supported:

•

Adapter Fault Tolerance (AFT)

•

Adaptive Load Balancing (ALB)

•

IEEE 802.3ad Dynamic Link Aggregation (DLA)

•

Static Link Aggregation (SLA)

•

Switch Fault Tolerance (SFT)

COM1

RS232, 115 kbps max., 9-pin SUB-D, male

Free slots for expansion

cards (see Motherboard

(Page 129))

Versions with 2 and 5 PCI(e) cards

For unique labeling, the Ethernet ports are numbered on the enclosure. The numbering by the

operating system can differ.

No teaming with AMT.

When using AMT, the interface X1P1 must be used for connection to remote maintenance.

An analog monitor can be used with an adapter cable (optional).

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands