Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 107 / 158

Maintaining and servicing your device

7.4 Removing and installing hardware

SIMATIC IPC677E
Operating Instructions, 04/2019, A5E45117996-AA

107

Procedure

Loosen the marked screws and remove the heat sink.

Release the lever of the processor bay and tilt it all the way back. The bay releases the

processor.

Remove the processor by grabbing the marked rails on the side. Do not touch the

processor and its connections in the process (see "ESD guidelines" under General safety

instructions (Page 25)).

Note
The contact springs of the socket are highly sensitive to mechanical damage, e.g. caused

by an incorrectly inserted CPU or foreign objects, and their entire surface may only touch

the contact side of the processor flat.

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands