Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 108 / 158

Maintaining and servicing your device

7.4 Removing and installing hardware

SIMATIC IPC677E

108

Operating Instructions, 04/2019, A5E45117996-AA

Install the new processor on the socket, as shown in the figure.
During positioning, make sure to take the highlighted arrow on the processor into

consideration.

Tilt the lever to the front again. Make sure that the bay covers the screw.

Press the lever all the way down and lock it again.

NOTICE
Damage to the processor due to excessive force
The locking mechanism may be stuck. The locking mechanism is damaged while being

pressed down.
The processor is not correctly locked in place by the bay. The result may be

malfunctions.

•

Do not use excessive force.

•

Tilt the lever back again and try again.

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands