Siemens SIMATIC IPC677E Operating Instructions Manual Download

Page: 39 / 158

Mounting and connecting the device

3.1 Preparing for mounting

SIMATIC IPC677E
Operating Instructions, 04/2019, A5E45117996-AA

3.1.5

Preparing the mounting cutout

Note
Stability of the mounting cutout
The material in the area of the mounting cutout must provide sufficient strength to guarantee

the enduring and safe mounting of the HMI device.
The force of the clamps or operation of the device may not lead to deformation of the

material in order to achieve the degrees of protection described below.

Note
Read the information in the section "Installation guidelines (Page 41)".

Requirements for complying with degree of protection

The degree of protection of the HMI device can only be guaranteed if the following

requirements are met:

●

Material thickness at the mounting cutout for IP65 degree of protection, or for

enclosure type 4X/type 12 (indoor use only): 2 mm to 6 mm

●

Permissible deviation from plane at the mounting cutout: ≤

0.5 mm

This condition must be fulfilled for the mounted HMI device.

●

Permissible surface roughness in the

area of the mounting seal: ≤

120 µm (R

120)

Dimensions of the mounting cutout

Summary of Contents for SIMATIC IPC677E































































































































































Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands

Siemens SIMATIC IPC677E, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC IPC677E

Reviews:

Related manuals for SIMATIC IPC677E

Brands by name

Popular brands